TPF may earn a commission from merchant affiliate
links, including eBay, Amazon, and others
I had the same concerns some time ago but, after being reassured on this site, dunked a light brown basic bag. Both the bag and glued in serial number were fine. I used tepid water to dunk and rinse.Has anyone dunked a bag with a glued in registration? I am mulling over a listing for a red basic bag and I have two concerns - color fade for a bag of that time period, and whether it will do harm to the bag itself or the adhesive on the registration number strip. ETA: I found an earlier conversation where a couple of people said they dunked with no issue to the registration strip but I still am curious to the opinions of other posters on both of my concerns![]()
It is really quite unbelievable that these bags can hold up SO well after so many years.I had the same concerns some time ago but, after being reassured on this site, dunked a light brown basic bag. Both the bag and glued in serial number were fine. I used tepid water to dunk and rinse.
I used “Spray 9” on a very dirty twill and leather bag (keeping away from the leather) and it came clean with very little effort.While waiting for my Lincoln E-Z Cleaner to arrive, and with some newly-minted eBay Bucks burning a hole in my digital wallet, I ordered this Convertible Clutch in Twill. I've never rehabbed a twill, but I'm up for a challenge. I bet I can use the Lincoln cleaner on this too!
View attachment 4630419
Thanks for the recommendation! If the Lincoln doesn't get it clean enough, I have an alternative to try.I used “Spray 9” on a very dirty twill and leather bag (keeping away from the leather) and it came clean with very little effort.
That spray cleaner, IMO is a miracle worker. I use it to pretreat laundry stains, to wipe my kitchen counter and stove top, clean spots on car seats and tire rims, etc.
I don't think there is much you can do. Every one of these I've seen has some problems with the brass. It isn't solid brass. I've always wanted one of these too.Ladies, I need your advice. and TIA.
I am trying to figure out the best way to clean and improve (or at least try), a damaged brass closure, with patina, verdigris...bad for what I can see in the pictures, it is still in the mail
Maybe I did wrong in getting the bag, but I always wanted one of that kind.
I have cleaned brass with the regular products, but perhaps there are different techniques if there is more damage....?
View attachment 4630651 View attachment 4630652 View attachment 4630653
So try the usual while praying, LOLI don't think there is much you can do. Every one of these I've seen has some problems with the brass. It isn't solid brass. I've always wanted one of these too.
Its on my ever incressing list.
Hrm, I'm no expert but I'd say masking off the leather from the brass (painters tape perhaps?) and attacking it carefully with some Brasso and a polishing tool might yield some nice results. Toothpicks on the verdigris around the edges might also allow you to get underneath the plate to the leather and scrape back some of the verdigris underneath. ETA: I picked up some dental-type picks from a local surplus store and they would probably get under that as well though they might scratch the leather underneath... yet nobody sees that under the plate, so I'd argue getting at the verdigris is more important.Ladies, I need your advice. and TIA.
I am trying to figure out the best way to clean and improve (or at least try), a damaged brass closure, with patina, verdigris...bad for what I can see in the pictures, it is still in the mail
Maybe I did wrong in getting the bag, but I always wanted one of that kind.
I have cleaned brass with the regular products, but perhaps there are different techniques if there is more damage....?
View attachment 4630651 View attachment 4630652 View attachment 4630653
I had one and polished it a little. It started to look worse, kind of scratched, so I stopped.Hrm, I'm no expert but I'd say masking off the leather from the brass (painters tape perhaps?) and attacking it carefully with some Brasso and a polishing tool might yield some nice results. Toothpicks on the verdigris around the edges might also allow you to get underneath the plate to the leather and scrape back some of the verdigris underneath. ETA: I picked up some dental-type picks from a local surplus store and they would probably get under that as well though they might scratch the leather underneath... yet nobody sees that under the plate, so I'd argue getting at the verdigris is more important.
Am I right in thinking that the lacquer is coming off of the plates as well? @whateve said it wasn't solid brass but is it brass-plated? If it's the lacquer coming off, polishing that off takes awhile but can yield pretty results. But if it isn't solid brass, I don't know if I'd recommend it. I'm conflicted!